該功能在測試共線操作變量(MVs)時有用。
智能向?qū)?yīng)用提供了允許一個MV（主要）與另一個MV（次要）配對的功能腾它，這樣當主MV階躍動作時乒裆，副MV亦同時做階躍動作璃俗。你可以通過STPAIRREQ參數打開或關閉此功能奴璃。
參數STPAIRRATIO定義了副MV與主MV的階躍大小之比。若比值為正城豁，則兩個MV將往相同方向做階躍苟穆。與此相反，若比值為負钮蛛，則兩個MV將往相反方向做階躍鞭缭。
配對變量必須配置在相同的測試組里。否則魏颓，智能向?qū)б鎸?huì)忽略MV配對要求。
當啟用一對配對MV時吱晒，主MV和副MV將同時做階躍動作甸饱。在測試組中主副MV的這一同時動作將被當成單個階躍。測試組在完成配對MV動作后在序列上進入下一MV仑濒。
只要配對MV在同一個測試組叹话，沒有限制哪個MV是主要的哪個MV是次要的。例如墩瞳，你可以指定MV2作為MV1（主要）的配對變量驼壶，而在同一時間指定MV1作為MV2（主要）的配對變量。
如果你在各自的STPAIRRATIO中依舊使用不同的標記喉酌，智能向?qū)б鎸⒆詣?dòng)生兩個不同的配對動作：一個同向热凹，一個反向。
附原文：
This feature may be useful for testing colinear manipulated variables (MVs).
A SmartStep application provides the functionality of allowing one MV (primary) to be paired up with another MV (secondary), such that when the primary MV steps, the secondary MV is simultaneously stepped also. You can turn this feature on or off via parameter STPAIRREQ.
The parameter STPAIRRATIO defines the ratio of the secondary MV step size over the primary MV. A positive ratio means both will step in the same direction. In contrast, a negative ratio will step the paired MVs in the opposite direction.
Paired variables must be configured in the same testing group. Otherwise, the SmartStep engine will ignore the MV pair request.
When a paired MV is enabled, both the primary and secondary MVs are stepped simultaneously.This simultaneous move of the primary MV step and secondary MV step is treated as a single step in the testing group. The testing group proceeds to the next MV in sequence on completion of the paired MV moves.
There is no restriction on which MV can be the primary and which should be secondary, as long as they are in the same testing group. For example, you can specify MV2 as a paired variable in MV1 (primary), while at the same time specifying MV1 as the paired variable in MV2 (primary).
If you also use different signs in the respective STPAIRRATIO, then the SmartStep engine will automatically generate two different paired moves: one in the same direction and the other in the opposite direction.
2015.10.17
